911 R-inspired

[40 scout]

Why can't bad companies be named and shamed ??

Fear of litigation ?

As long as the facts are clearly stated and true then why not speak out - save another customer the grief.

Steve

[hot66]

I think if you read Mick's very 1st post on page 1 of this thread, there might be some clues

[early_911]

I think if you read Mick's very 1st post on page 1 of this thread, there might be some clues

Yea, but two people are named.
Phil

[hot66]

I think if you read Mick's very 1st post on page 1 of this thread, there might be some clues

Yea, but two people are named.
Phil

I can only see one 'bodyshop' mentioned & I gather they did the work for Andy & for Mick

[domtoni]

Brembo reports this and I can verify it is not the same shop that did the work on Mick's car. It ( Brembo's ) is located in the south.

Similar story to yours Mick,had so called 'specialist' body shop' carry out conversion work to my car. Copious amounts of fillers used(12mm in some areas),atrocious paintwork and parts not fixed back onto car properly.This resulted in another company removing glass,and stripping back to bare metal,re-shaping some of the metal work,and complete re-spray.Worth it in the end,all be it a wee bit stressful at the time.It's a pity these companies can't be named and shamed.if only to prevent others from using there "specialist skills"

[Nige]

Mick your car has been up at MB Engineering for a while hasn't it? If so I had a little look around the car last time I was up there. Those rear arches are bad, overhung more on one side than the other. To be honest I though a new wing had been fitted over the top of the old one, but as your pictures show it was all filler

Good luck with getting it sorted.

[Barry]

What amazes me (and I don't want to get involved with who's done what to whom and when ) is that the actual shape in the filler must have taken ages, and no mean skill either.

I'd have thought it would have been quicker (not to mention more satisfying) to get it right in the metal, or at least within a m.m. or two.

Anyway, very best wishes with it Mick, it must be hard to remember this is all meant to be an enjoyable pastime at the moment. Still, Spring's around the corner, and those roads are waiting for you .

[domtoni]

+1 Barry.

[Barry]

Just a quick note, and this is with my (rather dusty, and very rarely worn) moderator's hat on.

I'm not quite sure how to word this, but I'll do my best.

I think as a forum, we might have to be little careful around the current subject matter. The facts seem to speak for themselves, and any involved parties are well known (and P.M.able). I wonder if therefore it might be an idea that we refrain from getting any closer to an open Name-N-Shame, tempting as it may be. I can see a situation where the forum, and Bootsy in particular, may get pulled into a situation it / he would rather not.

Perhaps therefore if someone considering a particular trader, or wishing to trade observations, might use the P.M. system. E.G. if Mr Bloggs was thinking about going to Mr Trader, but is worried about something that has happened to Mr Forum Member's car, perhaps Mr Bloggs might P.M. Mr Forum Member direct?

Sorry, I think that was probably one of the worst bits of writing I've ever smeared across this forum, but I hope the jist and spirit makes sense at least .

[Bootsy]

Makes sense to me, thanks Barry

[Viv_Surby]

Just a quick note, and this is with my (rather dusty, and very rarely worn) moderator's hat on.

I'm not quite sure how to word this, but I'll do my best.

I think as a forum, we might have to be little careful around the current subject matter. The facts seem to speak for themselves, and any involved parties are well known (and P.M.able). I wonder if therefore it might be an idea that we refrain from getting any closer to an open Name-N-Shame, tempting as it may be. I can see a situation where the forum, and Bootsy in particular, may get pulled into a situation it / he would rather not.

Perhaps therefore if someone considering a particular trader, or wishing to trade observations, might use the P.M. system. E.G. if Mr Bloggs was thinking about going to Mr Trader, but is worried about something that has happened to Mr Forum Member's car, perhaps Mr Bloggs might P.M. Mr Forum Member direct?

Sorry, I think that was probably one of the worst bits of writing I've ever smeared across this forum, but I hope the jist and spirit makes sense at least .

I think this is the best way forward....how about a sticky topic something like, "Thinking of using a trader? Ask away for expoeriences here" with replies by PM only??

Viv

[Mick Cliff]

I think this is the best way forward....how about a sticky topic something like, "Thinking of using a trader? Ask away for expoeriences here" with replies by PM only??
Viv

I agree with this

Just to be clear on my own feelings with this car....
I am not a litigious person;
I decided long ago to take a sanguine approach to this car;
I have spoken to several people who have had similar experiences;
I have shared my experience of this car with DDK to hopefully benefit anyone who may be thinking of taking a similar route.

What started as a 4-6 month project has now used up 18 months of my life but it will be on the road in Spring this year (famous last words?). I've plumbed the depths ranging from euphoria to despair. For a lot of the time I've been helped, materially and mentally, by inumerable DDK'ers, for which I am deeply grateful.

[Mick Cliff]

The root of the problem...

A DDK'er kindly sent me this picture of the OSR corner in its' original form before its' first build:


Sound metal, just dented (understatement!)

And this is it prior to the original planned paint 'refresh' and as I bought it



Feel a lot better now

[Mike]

What started as a 4-6 month project has now used up 18 months of my life

I know how you feel Mick, I'm just coming up to the 4th year of my 6 month project! Thing is you know you'll have a wonderful car at the end of it,
and it will have been worth all the work, hassle and expense in the end, honest.......

[domtoni]

Great idea Viv.