Handbrake racket not engaging
Moderators: drummerboytom, MdR
-
- Nurse, I think I need some assistance
- Posts: 7812
- Joined: Mon Apr 16, 2012 4:31 pm
Handbrake racket not engaging
The handbrake doesn't stay up. No clicking. Looks like there is a tab which should engage into the teeth if the racket but has become rounded? 1) my manual doesn't have a diagram of the handbrake so anyone have a link? So I can check my thinking 2). If I'm correct can I buy the tab on it's own?
If not I could try to make one if I can copied one or it's 200 eur for a new handbrake
Sent from my M2004J19C using Tapatalk
If not I could try to make one if I can copied one or it's 200 eur for a new handbrake
Sent from my M2004J19C using Tapatalk
“A REMINDER. I would be grateful if those members who have borrowed bits from me in emergencies (e.g starter motor, oil cooler, etc) would return them and/or contact me”. – Chris Turner RIP
-
- Put a fork in me, I'm done!
- Posts: 1672
- Joined: Fri Mar 01, 2013 11:45 am
- Location: Kernow - good old Cornwall
Re: Handbrake racket not engaging
As per usual GOOGLE is your friend. Do you have that search engine?
This persons video skills are on par with your photography, but it includes what you want. Basically just get someone to put a few welds on the end that’s worn away then file or grind the teeth back in again. The ratchet wears because people do not press the button when engaging the handbrake and just pull it up, so the teeth wear against the ratchet.
https://www.youtube.com/watch?v=HIg5JRe_72o
The bit you need is part number 901.424.508.00 (same as a 911 part)
Cheapest one to buy is here.......https://www.carpoint.de/en/original-paw ... _1333_2264
https://www.aasesales.com/collections/p ... 0130-31-12
https://www.rogerbrayrestoration.com/sh ... atch-pawl/
This persons video skills are on par with your photography, but it includes what you want. Basically just get someone to put a few welds on the end that’s worn away then file or grind the teeth back in again. The ratchet wears because people do not press the button when engaging the handbrake and just pull it up, so the teeth wear against the ratchet.
https://www.youtube.com/watch?v=HIg5JRe_72o
The bit you need is part number 901.424.508.00 (same as a 911 part)
Cheapest one to buy is here.......https://www.carpoint.de/en/original-paw ... _1333_2264
https://www.aasesales.com/collections/p ... 0130-31-12
https://www.rogerbrayrestoration.com/sh ... atch-pawl/
-
- Nurse, I think I need some assistance
- Posts: 7812
- Joined: Mon Apr 16, 2012 4:31 pm
Re: Handbrake racket not engaging
Thank you (I think)
Sent from my M2004J19C using Tapatalk
Sent from my M2004J19C using Tapatalk
“A REMINDER. I would be grateful if those members who have borrowed bits from me in emergencies (e.g starter motor, oil cooler, etc) would return them and/or contact me”. – Chris Turner RIP
-
- Nurse, I think I need some assistance
- Posts: 7812
- Joined: Mon Apr 16, 2012 4:31 pm
Re: Handbrake racket not engaging
Ok part bought. Does the pin/bolt holding it in knock out or is it riveted?
Sent from my M2004J19C using Tapatalk
Sent from my M2004J19C using Tapatalk
“A REMINDER. I would be grateful if those members who have borrowed bits from me in emergencies (e.g starter motor, oil cooler, etc) would return them and/or contact me”. – Chris Turner RIP
-
- Put a fork in me, I'm done!
- Posts: 1672
- Joined: Fri Mar 01, 2013 11:45 am
- Location: Kernow - good old Cornwall
Re: Handbrake racket not engaging
901.424.511.00
- AndrewSlater
- I luv DDK!
- Posts: 969
- Joined: Wed Nov 30, 2011 3:35 pm
Re: Handbrake racket not engaging
Hi Neil,
I think it is a push fit and peened in place not sure you can reuse the old one.
Discussion about it here.
http://forums.pelicanparts.com/porsche- ... lever.html
Regards
Andrew
I think it is a push fit and peened in place not sure you can reuse the old one.
Discussion about it here.
http://forums.pelicanparts.com/porsche- ... lever.html
Regards
Andrew
1966 Porsche 912 Slate Grey, red interior - first owner owned for 41 years
1974 Porsche 911 2.7 (The Manhattan project) viewtopic.php?f=28&t=51455
1973 VW 914 1.7 Olympic Blue - ( gone to a good home )
1974 Porsche 911 2.7 (The Manhattan project) viewtopic.php?f=28&t=51455
1973 VW 914 1.7 Olympic Blue - ( gone to a good home )
-
- Nurse, I think I need some assistance
- Posts: 7812
- Joined: Mon Apr 16, 2012 4:31 pm
Re: Handbrake racket not engaging
Thank you. I bgt the part from Porsche. I should of done that with the other bit too. Saves on postage
Sent from my M2004J19C using Tapatalk
Sent from my M2004J19C using Tapatalk
“A REMINDER. I would be grateful if those members who have borrowed bits from me in emergencies (e.g starter motor, oil cooler, etc) would return them and/or contact me”. – Chris Turner RIP
-
- Put a fork in me, I'm done!
- Posts: 1672
- Joined: Fri Mar 01, 2013 11:45 am
- Location: Kernow - good old Cornwall
Re: Handbrake racket not engaging
Here you go a cheapie SEALED BEAM unit on Ebay for your hollybobs drive
https://www.ebay.co.uk/itm/222281590022 ... =580548181
https://www.ebay.co.uk/itm/222281590022 ... =580548181
-
- Nurse, I think I need some assistance
- Posts: 7812
- Joined: Mon Apr 16, 2012 4:31 pm
Re: Handbrake racket not engaging
Many thanks for all the help. Turns out the part had rotated. Once I got it off it looked as good as the new part I had bought. Of course I then put it back on the wrong way so had to remove and reinstall again. I tried to punch the old rivet out but it only moved a bit so ended up widening the gap with screw drivers while Mrs B removed and installed it.
All working again. Test drive tomorrow
Sent from my M2004J19C using Tapatalk
All working again. Test drive tomorrow
Sent from my M2004J19C using Tapatalk
“A REMINDER. I would be grateful if those members who have borrowed bits from me in emergencies (e.g starter motor, oil cooler, etc) would return them and/or contact me”. – Chris Turner RIP