O/T - Der uber-shed
Moderators: hot66, Miggs, 58A - 71E, impmad2000, drummerboytom, Barry, Helen, Viv_Surby, Derek, KS, abm914, Mike Usiskin
-
- DDK 1st, 2nd and 3rd for me!
- Posts: 2062
- Joined: Wed Jun 23, 2004 9:47 pm
- Location: Nottinghamshire
Re: O/T - Der uber-shed
Looks fantastic, well done. Love the attention to detail. I assume you will not be doing any fab work in there before the wedding for fear of ruining the finish and getting everything generally covered in crap? Or is it storage only, and you have a separate working area?
I have been doing my own ‘side project’ this summer using sleepers as uprights for a building in the garden that is bearing a living roof. I have the hernia to prove it, so share your pain!
I have been doing my own ‘side project’ this summer using sleepers as uprights for a building in the garden that is bearing a living roof. I have the hernia to prove it, so share your pain!
93 964 C2
99 Boxster 2.5 > 2.7 hill climber
71 914/6 3.0 - gone
'You see Paul, hill climbing is like making love to a beautiful woman. You get your motor running, check your fluids, hang on tight and WHOA..30 seconds later it's all over!' Swiss Tony
99 Boxster 2.5 > 2.7 hill climber
71 914/6 3.0 - gone
'You see Paul, hill climbing is like making love to a beautiful woman. You get your motor running, check your fluids, hang on tight and WHOA..30 seconds later it's all over!' Swiss Tony
- Nige
- Nurse, I think I need some assistance
- Posts: 6601
- Joined: Wed Nov 26, 2003 9:11 pm
- Location: Denby, Derbyshire
Re: O/T - Der uber-shed
Nice work on the sleeper cutting jig, it's tough trying to keep your cuts straight on that stuff.
I like the steel conduit too, I used the same in my cabin although used Conlok to avoid threading the bar.
I like the steel conduit too, I used the same in my cabin although used Conlok to avoid threading the bar.
- Bootsy
- Site admin and the Boss
- Posts: 23978
- Joined: Sat Nov 08, 2003 6:09 pm
- Location: Norwich
- Contact:
Re: O/T - Der uber-shed
Now that is a great idea.DustyM wrote: Once the weddings out the way you can throw a DDK party
Looking superb Mark
1972 911T | 1994 993 Carrera | 1999 986 Boxster | 1990 T25 Camper
Vintage Heuer, Omega, Zenith and other vintage watches - http://www.heuerheritage.co.uk
Vintage Heuer, Omega, Zenith and other vintage watches - http://www.heuerheritage.co.uk
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
Thanks guys
Keith my tyres are Toyo Proxes - I think that’s T1 but can’t be sure. I’ve run them for about 20 years now and really like them
Hernia!! Those sleepers are bloody heavy though
Keith my tyres are Toyo Proxes - I think that’s T1 but can’t be sure. I’ve run them for about 20 years now and really like them
Hernia!! Those sleepers are bloody heavy though
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- DDK 1st, 2nd and 3rd for me!
- Posts: 2062
- Joined: Wed Jun 23, 2004 9:47 pm
- Location: Nottinghamshire
Re: O/T - Der uber-shed
Sadly yes, I should have got a machine in, but stupidly chose to dig everything by hand. The sleepers are set vertically and with a 7.5 degree pitch for drainage, so as well as being square I had to set them at exactly the right height; 70kgs in, then out, then in, then out Chuckle Brothers style from 80cm deep holes. It is fair to say my body told me I am not 30 any more.sladey wrote:Thanks guys
Keith my tyres are Toyo Proxes - I think that’s T1 but can’t be sure. I’ve run them for about 20 years now and really like them
Hernia!! Those sleepers are bloody heavy though
I did find that a borrowed big chop saw would cut the sleepers, but only after I had done 10 of them. Your solution is much nicer!
Sent from my iPhone using Tapatalk
93 964 C2
99 Boxster 2.5 > 2.7 hill climber
71 914/6 3.0 - gone
'You see Paul, hill climbing is like making love to a beautiful woman. You get your motor running, check your fluids, hang on tight and WHOA..30 seconds later it's all over!' Swiss Tony
99 Boxster 2.5 > 2.7 hill climber
71 914/6 3.0 - gone
'You see Paul, hill climbing is like making love to a beautiful woman. You get your motor running, check your fluids, hang on tight and WHOA..30 seconds later it's all over!' Swiss Tony
- Nige
- Nurse, I think I need some assistance
- Posts: 6601
- Joined: Wed Nov 26, 2003 9:11 pm
- Location: Denby, Derbyshire
Re: O/T - Der uber-shed
Did you watch this video Mark
https://www.youtube.com/watch?v=o1T3-4TOv1w
https://www.youtube.com/watch?v=o1T3-4TOv1w
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
Not seen that before Nige - interesting stuff. I had to work it all out for myself. My pipe bender doesn't have degrees marked on it - but when doing the swan necks I marked a line to bend to for the main bend.
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
OK probably time for a bit of an update…..
Garage doors got painted which was nice
And I made some sturdy brackets to hold the electric door opening rams
I got a couple of roller cabinets from SDS to fit amongst the built in cabinets I was going to make
They aren’t great quality but not bad either. However as they are going to be in a run of units I wanted the handle to be down the side instead of along one edge
Et voila
Sent from my iPad using Tapatalk
Garage doors got painted which was nice
And I made some sturdy brackets to hold the electric door opening rams
I got a couple of roller cabinets from SDS to fit amongst the built in cabinets I was going to make
They aren’t great quality but not bad either. However as they are going to be in a run of units I wanted the handle to be down the side instead of along one edge
Et voila
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
- Nige
- Nurse, I think I need some assistance
- Posts: 6601
- Joined: Wed Nov 26, 2003 9:11 pm
- Location: Denby, Derbyshire
Re: O/T - Der uber-shed
Looking great Mark, when is the grand opening party?
You also need some of my Garage Storage system in there:
https://www.thebikehanger.co.uk/bike-ha ... e-storage/
I'll do you a discount
You also need some of my Garage Storage system in there:
https://www.thebikehanger.co.uk/bike-ha ... e-storage/
I'll do you a discount
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
I wanted the roller cabinets in first because I wanted to build the run of cabinets around them.
One of my Christmas presents was this square which has been absolutely fantastic for setting up the frames for welding
Sent from my iPad using Tapatalk
One of my Christmas presents was this square which has been absolutely fantastic for setting up the frames for welding
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
I’ve made all the frames out of 50x50 square tube, which weighed the camper down when I picked it all up
Sent from my iPad using Tapatalk
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
It takes a while to get the frames all made up - bit of a ball-ache really
I wanted adjustable feet for them all so I could get them just right. I eventually hit upon the idea of using ice-hockey pucks (there are a few YouTube vids out there on this - not my idea)
And eventually you end up with this
Which fix into place like this
Sent from my iPad using Tapatalk
I wanted adjustable feet for them all so I could get them just right. I eventually hit upon the idea of using ice-hockey pucks (there are a few YouTube vids out there on this - not my idea)
And eventually you end up with this
Which fix into place like this
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
After a while I’d got a load of them done.
The plan is to build wooden cabinets (drawers or cupboards) within the frames.
Around this time (spring 2022) my focus started to change. My middle daughter was getting married at the end of May and was planning on having the wedding reception in my barn.
I therefore had to focus on things other than the cabinets.
Sent from my iPad using Tapatalk
The plan is to build wooden cabinets (drawers or cupboards) within the frames.
Around this time (spring 2022) my focus started to change. My middle daughter was getting married at the end of May and was planning on having the wedding reception in my barn.
I therefore had to focus on things other than the cabinets.
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 8796
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: O/T - Der uber-shed
First was the low door at the end of the room.
It looked a real mess so first I had a builder who tidied it up a bit and made the floor frame safer.
Then I needed a door. A short, wide door. I also wanted it to be a sliding door, as any sort of opener would block the little corridor it would open into.
I didn’t have a short wide door, but I did have the original two garage doors. Both were tall and too narrow
I started by chopping the sides off one of them
And then I needed to shorten the one I was gong to use. When I shortened them it took the horizontal support away - so I cut that down to fit
Like this
It was starting to come together now
And then I added the sides on (with domino joints)
Leading to the short wide door I wanted
Sent from my iPad using Tapatalk
It looked a real mess so first I had a builder who tidied it up a bit and made the floor frame safer.
Then I needed a door. A short, wide door. I also wanted it to be a sliding door, as any sort of opener would block the little corridor it would open into.
I didn’t have a short wide door, but I did have the original two garage doors. Both were tall and too narrow
I started by chopping the sides off one of them
And then I needed to shorten the one I was gong to use. When I shortened them it took the horizontal support away - so I cut that down to fit
Like this
It was starting to come together now
And then I added the sides on (with domino joints)
Leading to the short wide door I wanted
Sent from my iPad using Tapatalk
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Nurse, I think I need some assistance
- Posts: 16903
- Joined: Wed Nov 12, 2003 10:48 pm
- Location: Worcs/W Mids border
Re: O/T - Der uber-shed
.
Impressive work Mark !!
That's going to be a fantastic workspace by the time it's finished.
.
Impressive work Mark !!
That's going to be a fantastic workspace by the time it's finished.
.
Andy
“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”
“Adding power makes you faster on the straights;
- subtracting weight makes you faster everywhere”