Restoration of my 1971 911T Targa
Moderator: Bootsy
-
- Nurse, I think I need some assistance
- Posts: 19013
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Restoration of my 1971 911T Targa
I would be interested to see a pic of the RHD conversion panel you removed unless it's in the skip!
I know a company who cut the dash to swop the column over and the dial panel, bet it was one of theirs.
I know a company who cut the dash to swop the column over and the dial panel, bet it was one of theirs.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Restoration of my 1971 911T Targa
Hi, unfortunately I don't have the RHD conversion panel although there is a picture of the main cut out sections of bodywork below:
It does show the 'cut and shut' dash and other parts various. It probably isn't particularly helpful.
Cheers, Neil
It does show the 'cut and shut' dash and other parts various. It probably isn't particularly helpful.
Cheers, Neil
-
- Nurse, I think I need some assistance
- Posts: 19013
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Restoration of my 1971 911T Targa
Thanks for the pic, understandably in the pile.
I've seen just 2 of these conversions where the LHD panel of the dash is simply cut out, sectioned and welded back in and gap left all over the place, the dash top covering the lot.
I did my own conversion 27 years ago but using Porsche panels and RHD pedals etc, hence my interest.
I've seen just 2 of these conversions where the LHD panel of the dash is simply cut out, sectioned and welded back in and gap left all over the place, the dash top covering the lot.
I did my own conversion 27 years ago but using Porsche panels and RHD pedals etc, hence my interest.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Restoration of my 1971 911T Targa
I remember your write up of the Conversion you completed. Mine sounds similar to the ones you have seen.
The resulting dashboard was odd in that, despite everything looking sort of reasonable having the heater on the RHS of the steering wheel and the Ignition switch on the LHS of the steering wheel was peculiar. Obviously parts of the dash were cut and relocated with the minimum amount of effort. The steering column tube requires modification which I have done which they didn't bother with back in the day (obviously).
I think the new (to the car) dash/bulkhead cut is going to be prepped and put in the place next week/week after and the doors are going to be hung in readiness for the sills to be finished. It will be quite exciting to see it coming that close to completion.
Cheers, Neil
The resulting dashboard was odd in that, despite everything looking sort of reasonable having the heater on the RHS of the steering wheel and the Ignition switch on the LHS of the steering wheel was peculiar. Obviously parts of the dash were cut and relocated with the minimum amount of effort. The steering column tube requires modification which I have done which they didn't bother with back in the day (obviously).
I think the new (to the car) dash/bulkhead cut is going to be prepped and put in the place next week/week after and the doors are going to be hung in readiness for the sills to be finished. It will be quite exciting to see it coming that close to completion.
Cheers, Neil
Re: Restoration of my 1971 911T Targa
Excellent project ... the kind of thing we only seem to find here on DDK.
The freight bill on getting that whole floor to NZ must have been significant in and of itself?
Best, John
The freight bill on getting that whole floor to NZ must have been significant in and of itself?
Best, John
Re: Restoration of my 1971 911T Targa
Yes the floor-pan was quite expensive to ship (below is a snip of the invoice $NZ) GST to be added on top...
Petrol Tank came up quite well. There is just a little bit of rust in one area which, I believe, is good to treat with Rust Inhibitor and I will treat the tank to Por15 Petrol Tank sealant.
This is the general view of the tank
Here is a close-up of the rust
Just some last tidying up of the Petrol Tank, Rust Inhibitor and application of the Por15 Petrol Tank sealant.
I will then prime and apply the Stone Chip paint and top coat
Cheers, Neil
Petrol Tank came up quite well. There is just a little bit of rust in one area which, I believe, is good to treat with Rust Inhibitor and I will treat the tank to Por15 Petrol Tank sealant.
This is the general view of the tank
Here is a close-up of the rust
Just some last tidying up of the Petrol Tank, Rust Inhibitor and application of the Por15 Petrol Tank sealant.
I will then prime and apply the Stone Chip paint and top coat
Cheers, Neil
-
- DDK slapper chatter
- Posts: 444
- Joined: Mon Feb 18, 2008 2:05 pm
- Location: Co. Down, N.Ireland
Re: Restoration of my 1971 911T Targa
Hi. Your petrol tank worries me a little. I'd get it leak tested before use.
If you are talking about sealing the tank inside I think people have had mixed results with that. The sealant broke down gradually on a friends car and was eventually identified as the cause of rough running due to blockage caused by loose sealant.
Finally, once you're sure it is not leaking and is well rust treated, you can get stone chip that can be coloured. That would be a better job than top coat.
Best.
Al.
If you are talking about sealing the tank inside I think people have had mixed results with that. The sealant broke down gradually on a friends car and was eventually identified as the cause of rough running due to blockage caused by loose sealant.
Finally, once you're sure it is not leaking and is well rust treated, you can get stone chip that can be coloured. That would be a better job than top coat.
Best.
Al.
DDK#732
1981 SC Coupe, now in Dublin
1978 SC Targa, now in Aberdeen
1978 SC Coupe, now in London
1983 SC Coupe, now in London
1973 2.4T...under restoration...VERY slow restoration.
1981 SC Coupe, now in Dublin
1978 SC Targa, now in Aberdeen
1978 SC Coupe, now in London
1983 SC Coupe, now in London
1973 2.4T...under restoration...VERY slow restoration.
Re: Restoration of my 1971 911T Targa
Thanks Al for your advice with regards the petrol tank. I have made quite a bit of progress with it. I completed cleaning it up and got rid of 99% of the rust. I then used Rust Converter. It is looking pretty good. I will fill the tank up and check for any leaks prior to undertaking any treatment. I have sought the advice of an experienced welder who said that the tank was in reasonable condition.
I have left it one side for now and moved on to the rear lights. They need a fair amount of attention. One of the lights has been battered about and needs straightening. Both need cleaning up and the reflective surfaces recoating (if that is possible). I will then look into the H1 headlights. Mechanically and electrically they are good but the reflectors are fairly poor. I will see about taking all four units to get them recoated.
Cheers, Neil
I have left it one side for now and moved on to the rear lights. They need a fair amount of attention. One of the lights has been battered about and needs straightening. Both need cleaning up and the reflective surfaces recoating (if that is possible). I will then look into the H1 headlights. Mechanically and electrically they are good but the reflectors are fairly poor. I will see about taking all four units to get them recoated.
Cheers, Neil
Re: Restoration of my 1971 911T Targa
Before anyone spots the deliberate mistake that is my battered RHS rear light - soon to be straightened out and 'spiffed up'.
Incidentally does anyone know whether the reflectors in H1 headlights are 'silvered' or are they 'vapor deposited aluminium' coated?
Thanks in advance if anyone can confirm.
Cheers, Neil
Incidentally does anyone know whether the reflectors in H1 headlights are 'silvered' or are they 'vapor deposited aluminium' coated?
Thanks in advance if anyone can confirm.
Cheers, Neil
Re: Restoration of my 1971 911T Targa
Work continues on my car. I am part way through the Petrol tank. I have painted the exterior and am awaiting a few hours to treat the inside with POR15 petrol tank sealer. I have stripped the headlights (H1s) and decided that the reflectors need re-plating. I struggled to find anyone that can re-plate them in New Zealand so they are off to Australia! Replacements were going to cost too much and I didn't like the idea of the re-imagined H1 headlights that you can buy. I like the idea of restoring my original ones.
Cheers, Neil
Cheers, Neil
Re: Restoration of my 1971 911T Targa
I have continued on with work. I have been getting parts vapour blasted and the results are really pleasing enabling parts that look past their best to be repaired, plated, painted or whatever suits.
Work continues...
Cheers, Neil
Work continues...
Cheers, Neil
Re: Restoration of my 1971 911T Targa
I started the stone-chipping of my petrol tank. I was only able to add a single coat.
I will continue this evening.
The rear discs cleaned up beautifully. I will paint the 'drum part' to protect from future rust...
Cheers, Neil
I will continue this evening.
The rear discs cleaned up beautifully. I will paint the 'drum part' to protect from future rust...
Cheers, Neil
Re: Restoration of my 1971 911T Targa
Further cleaning up of the Rear Lights reveals pitting and some holes. The RHS light had a crack and playing around with trying to adjust the metalwork resulted in a chuck coming away. I have re-inserted this part and acquired some metal filler to tidy these up. There are areas missing also that need to be built back up. I am confident these Rear Lights will look really good once I am finished.
I will update as I go. I am going to use chrome reflective paint on the reflector areas and silver on the exterior. New seals (etc.) are on their way.
Cheers, Neil
I will update as I go. I am going to use chrome reflective paint on the reflector areas and silver on the exterior. New seals (etc.) are on their way.
Cheers, Neil
-
- Nurse, I think I need some assistance
- Posts: 10320
- Joined: Wed Mar 31, 2004 1:27 pm
- Location: Cheshire
- Contact:
Restoration of my 1971 911T Targa
If you get stuck on reinstating that build holder you can drill out the hole and put a bulb holder in instead.
Re: Restoration of my 1971 911T Targa
Gary, that is great to know. I was planning on re-instating the circuit board. Someone had already butchered/repaired one and used a hefty amount of red silicon gunk to hold the circuit board in place.
Changing out to bulb holders is definitely a great Plan B.
Cheers, Neil
Changing out to bulb holders is definitely a great Plan B.
Cheers, Neil