Door fit - 356 rep

Replica owners or enthusiasts are very welcome

Moderator: Bootsy

Post Reply
bonerp
DDK slapper chatter
Posts: 440
Joined: Mon Jun 21, 2010 9:16 am

Door fit - 356 rep

Post by bonerp »

Hi
Have a Pilgrim and the bottom edge of the door almost touches the sill. The sill seems to hump up very slightly, if you know what i mean...

Just about to be painted so is there any solution to this??

thanks
Paul
Built a Pilgrim Speedster...only down one kidney

My build: https://sites.google.com/site/bonerp356/home

http://www.Speedsterclinic.co.uk

Now for sale! Next project looms...
mdmax72
Put a fork in me, I'm done!
Posts: 1512
Joined: Thu Sep 28, 2006 8:23 pm
Location: midlands u.k

Post by mdmax72 »

Paul,
you either take some of the door bottom to match the sill or sand back the sill to match the door. If only slight taking of the door would be easier. What colour have you gone for..

Regards Rich
oliver365
DDK slapper chatter
Posts: 463
Joined: Sun Oct 25, 2009 8:25 am
Location: cheshire

door fit

Post by oliver365 »

Rich I had the same prob with my Pilgrim as u will see if u look back on this forum .I had a lot of ill fitting parts , Mr Tanner admitted 2 me that thay just lay the body on the floor after coming out of its mould! as u no the sills are the weakest points so thay will bow if not on a jig .To sort the prob I got some resin & glass off Mr Tanner & I got some stainless steel angle ,screwed the sills straight & fibre glassed in upside down .Also look at the doors that the 2 skins r bonded together properly (mine werent)my boot was awfull as well so I got a new boot off him but not bonded together so I could get it to fit correct! good luck :?
mdmax72
Put a fork in me, I'm done!
Posts: 1512
Joined: Thu Sep 28, 2006 8:23 pm
Location: midlands u.k

Post by mdmax72 »

Pictures would be best, so we know what slightly is??

Regards
bonerp
DDK slapper chatter
Posts: 440
Joined: Mon Jun 21, 2010 9:16 am

Post by bonerp »

Image
best pic I have. I will be having condor yellow. Going into the paint shop this week to try to fix doors. Also my boot lid is naff and will be filled to meet the edge of the body properly. The bonnet is too long as well!!! And yes the door has split apart in places and needs some fibre glass running along the seams grrr

Oliver, not sure I quite understand - are you saying fix a bracket under the sill to pull it down?
Built a Pilgrim Speedster...only down one kidney

My build: https://sites.google.com/site/bonerp356/home

http://www.Speedsterclinic.co.uk

Now for sale! Next project looms...
mdmax72
Put a fork in me, I'm done!
Posts: 1512
Joined: Thu Sep 28, 2006 8:23 pm
Location: midlands u.k

Post by mdmax72 »

l think what oliver did was get some steel/stainless angle the length of the sill. From under the car position the sill closest to the outside edge and drill and screw from above. Use self drill countersink screws. This will clamp the body(sill) to the steel underneath. The rubber mat on the door threshold will hide the screws. Better do this before paint though. Let us know how you get on. Did your wife forgive you for talking about cars when l phoned you on your camping trip?? 8)

Rich
Last edited by mdmax72 on Fri Aug 13, 2010 10:12 pm, edited 1 time in total.
bonerp
DDK slapper chatter
Posts: 440
Joined: Mon Jun 21, 2010 9:16 am

Post by bonerp »

haha yes just about - we had just started putting the tent up when you rang! Perfect timing :lol:
Built a Pilgrim Speedster...only down one kidney

My build: https://sites.google.com/site/bonerp356/home

http://www.Speedsterclinic.co.uk

Now for sale! Next project looms...
Post Reply