Engine stand yoke

Beetlejac · Post by **Beetlejac** » Mon May 14, 2012 4:56 pm

Engine yoke is constructed of thickwall steel pipe and cnc plasma cut 6mm heavy plate steel.
Fits all air-cooled VW and Porsche engines/transaxles.Engine mounting ring and four arm design reduces the chance of case damage. Engine yoke fits most roll-round stands(Clark/sealy)with a 60mm ID.£70 plus £10 post
jack.purse@outlook.com

chaos · Post by **chaos** » Sun May 27, 2012 6:25 pm

hia, is this for allI can see, as in stand and the two spiders?
cheers dave

Beetlejac · Post by **Beetlejac** » Mon May 28, 2012 7:54 pm

No just the YOKE,thats the black bit,and just the one.
thanks
jack

911hillclimber · Post by **911hillclimber** » Sat Jun 02, 2012 6:33 pm

Will this fit a 3.2 911 engine?
Not sure if your description means all 4 cylinder engines or includes the 6 cylinder?

butzsi · Post by **butzsi** » Sat Jun 02, 2012 7:38 pm

I think marginal Graham as 3.2 with stock equipment is close to the SWL - does not allow much leeway if you are undoing camshaft nuts at 100 ft/lbs. Do you have steelcap boots?

Regards...Chris

911hillclimber · Post by **911hillclimber** » Sat Jun 02, 2012 8:13 pm

That is why I asked!
The 3.2 is a mighty lump fully dressed.

Beetlejac · Post by **Beetlejac** » Sat Jun 02, 2012 9:45 pm

Hi that SWL you see is for the actual stand not the yoke/spider,l have been making the rings wider so they look stronger and have more surface contact and at the end of the day its only realy two M10 bolts thats holding the engine on the yoke/spider.
The welds are'nt going to fail and with the weight spread over the four arms l cant see them failing and bending.The yoke's only as good as the stand its mounted to.
Hope that helps
jack

Beetlejac · Post by **Beetlejac** » Sun Jun 24, 2012 9:04 pm

Bench mounted,heavy duty £90

carrera79 · Post by **carrera79** » Tue Jun 26, 2012 11:51 am

Beetlejac wrote:Bench mounted,heavy duty £80

do you sell this ?

fred

©

Beetlejac · Post by **Beetlejac** » Tue Jun 26, 2012 9:01 pm

Yes mate.
cheers
jack
Beetlejac72@aol.com

911hillclimber · Post by **911hillclimber** » Sun Jul 01, 2012 6:38 pm

I would actually like to buy one of your Yokes, heavy duty, not with the bench mounting, but for the engine stand tube.

Please pm the cost to me.
Do you take paypal, and are these 'in stock' so to speak?
If not how long is your lead time?

Thanks,
Graham.

Beetlejac · Post by **Beetlejac** » Sun Jul 01, 2012 9:35 pm

PM sent.

911hillclimber · Post by **911hillclimber** » Tue Jul 03, 2012 5:40 pm

Job done.

visualfx · Post by **visualfx** » Wed Jul 04, 2012 12:56 am

I'd like a bench mounted one please?

911hillclimber · Post by **911hillclimber** » Mon Jul 09, 2012 6:05 pm

Mine arrived today, looks good and fits my Clark stand a treat.

It needs a 10mm hole(s) drilling to secure the 'angle' of the frame as you work on the engine, but no problem.
Chuffed!
Graham.

DDK - Die Deutschen Klassiker

Engine stand yoke

Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke

Re: Engine stand yoke