D'Eser seats

Mick Cliff · Post by **Mick Cliff** » Fri Jan 07, 2011 9:56 pm

pb911 wrote:Seats look good, I think that wheel is a 380mm though !

You're right of course

I've corrected the original post

Thanks again for the Christmas spirit

hot66 · Post by **hot66** » Sat Jan 08, 2011 7:51 am

Looking good Mick

yoda · Post by **yoda** » Sat Jan 08, 2011 3:44 pm

Thanks for the info Mick. I think they look superb.

How do you find the tilting mechanism? Probably another question to answer with a bit of use but would be interested to hear what you think.

Regards

domtoni · Post by **domtoni** » Sat Jan 08, 2011 6:31 pm

Glad you are happy Mick. Over the years I spent alot of time getting to know Cesere, and I was always impressed by his work.

Mick Cliff · Post by **Mick Cliff** » Sun Jan 09, 2011 5:38 am

yoda wrote:How do you find the tilting mechanism?

It's quite limited but useful. Ideal for small people but there's still the trip hazard of the seatbelt fixed to the seat frame. Basically it gives you enough room to chuck luggage into the back and strap it down. An improvemnt on what I had before - Corbeau buckets on non-tilting frames

At least I can get into the back to vacuum it out and clean the rear glass now

yoda · Post by **yoda** » Sun Jan 09, 2011 10:34 am

Sounds like they are ideal Mick. I would just be wanting little people in the back so should be fine as long as they don't trip on the way in.

Thanks for all the feedback, much appreciated.

Regards

mycar · Post by **mycar** » Thu Jan 13, 2011 7:13 pm

Sorry Mick, missed this. The seats look fantastic, I`m glad you`re pleased with them.

Cultivating some rust on the floor pan to complement the colour scheme is a very clever idea, will you be putting a coat of clear laquer over it ?

Looking forward to seeing the seats in person,

Mike.

niels · Post by **niels** » Thu Jan 13, 2011 8:01 pm

Mick they look fantastic. Did they make you frames without the distance bushes?

I will post when I got them removed. Started a new quite distracting project (recovering a 1300 GTJ Bertone with 2000 engine

)

Mick Cliff · Post by **Mick Cliff** » Fri Jan 14, 2011 4:24 am

mycar wrote:Sorry Mick, missed this. The seats look fantastic, I`m glad you`re pleased with them.
Cultivating some rust on the floor pan to complement the colour scheme is a very clever idea, will you be putting a coat of clear laquer over it ?
Looking forward to seeing the seats in person,
Mike.

Rust? Where? There's no rust in there Mike! It's the original (body colour) paint that's fooling you

niels · Post by **niels** » Fri Jan 14, 2011 8:26 am

mick, can you post a picture of the side of the brackets? Particularly the part where the rails meet the black coloured metal. On top of that I'm interested how they solved the handle to operate the rails for the sliding mechanism

Mick Cliff · Post by **Mick Cliff** » Fri Jan 14, 2011 10:55 am

Niels
Hope these help - seats now fitted so difficult to get exactly what you need.
If you need any more info then let me know and I'll try to help.

niels · Post by **niels** » Fri Jan 14, 2011 6:49 pm

Thanks Mick, difficult to see on your pics. Please look at a pic from me.

The bushes are inside the red ovals.

PhilGarner · Post by **PhilGarner** » Fri Jan 14, 2011 10:44 pm

Seats look great Mick, definite case of seat envy from me.

niels · Post by **niels** » Tue Jan 18, 2011 7:04 pm

Mick, do your brackets have these bushes?

Mick Cliff · Post by **Mick Cliff** » Tue Jan 18, 2011 9:03 pm

Sorry Niels, forgot to look last time

Just been and had a look now - can't see anything like those bushes.