Page 66 of 66

Re: 912 outlaw project

Posted: Mon Sep 09, 2024 7:05 pm
by Bootsy
Like those

Re: 912 outlaw project

Posted: Fri Sep 26, 2025 5:04 pm
by jury

Re: 912 outlaw project

Posted: Sat Sep 27, 2025 10:47 am
by sladey
Enjoyed that video Chris. Car still looking cool

Re: 912 outlaw project

Posted: Sat Sep 27, 2025 12:00 pm
by jb
Great to see and hear you Chris

Re: 912 outlaw project

Posted: Sun Mar 08, 2026 8:05 pm
by jury
Time for some improvements...cos they are never really finished :)

I needed to have look at the wiring, there's been a few occasions when the car has refused to start, after upgrading starter motors and batteries the next part to look at was the wiring. More so, making sure that the earths where earthing.

This looks worse than it was, but the more I started to unwrap the loom the more I could see where things could be more "efficient". Also decided to remove the Heated windscreen circuit and generally try and simplify things bit more.....

Image

Image

Looks a mess but wasn't that bad :)

Image


New Fuse holder made up...

Image

...but decided it would be way cooler to try and replicate the the amber tinware, so a trip to the local craft shop and the liberation of a baking tray....

Image

Image

Image

Image

Waste not want not....

Image

Image


With that, time to put it all back together and make sure that point A to B is as simple as possible.....

Image

Re-wrap and sleeve

Image

Image

Image

Image


and remarkably it all still works, only better ! (once I realized that the fuel pump and starter solenoid wires were the wrong way around :shock: )


Chris

Re: 912 outlaw project

Posted: Sun Mar 08, 2026 9:18 pm
by Lightweight_911
.

That's a great result Chris - it all looks very neat ... not that I would have expected anything else ! 8)


.

Re: 912 outlaw project

Posted: Mon Mar 09, 2026 8:42 pm
by Darren65
Simply brilliant! 8) :thumbleft:

Re: 912 outlaw project

Posted: Fri Mar 13, 2026 8:54 pm
by jtparr
That definitely appeals to my OCD nature…love the curves in the wiring loom

Re: 912 outlaw project

Posted: Tue Mar 17, 2026 5:50 am
by jury
jtparr wrote: Fri Mar 13, 2026 8:54 pm That definitely appeals to my OCD nature…love the curves in the wiring loom
A to B as efficiently as possible :)

Re: 912 outlaw project

Posted: Thu Apr 23, 2026 4:44 am
by jury
A few more Mods

Never been able to see clearly out of the rear view mirror...seat position, roll bar etc etc. Even attaching the mirror to the windscreen didn't really work......so the most sensible option is obviously attaching it to the dashboard :) . Found a pre-dilled trim hole, not bad, but about abit clunky...

Image

Image

Image


Don't tell Mick Cliff, but we have finally found a home for "that" mirror some 18 years later !! :)

Image


A slight shortening of the stem, abit of JB weld, black paint and found another pre-dilled trim hole...

Image

Image

Image

Re: 912 outlaw project

Posted: Thu Apr 23, 2026 4:58 am
by jury
Whilst reading about / lusting over 964 RS N-GT's, it was mentioned that the wooden floor boards / "mats" help prevent foot slippage when its bit damp outside.....also flatting the floor pan lumps and bumps, plus they look cool!

Image

Image

Image

Re: 912 outlaw project

Posted: Thu Apr 23, 2026 4:59 am
by Mick Cliff
jury wrote: Thu Apr 23, 2026 4:44 am Don't tell Mick Cliff, but we have finally found a home for "that" mirror some 18 years later !! :)
18 years really? Told you I was right... :lol: