DDK - Die Deutschen Klassiker

I had taken the front hubs to a local machine shop to machine the back plate and TIG weld adaptors for the front Porsche 968 calipers. Unfortunately after 8 weeks they are too busy to complete. I have found another shop, run by a gentleman who specialises in race fabrication work, but only works part time. At least he has agreed to complete the work as its something unusual. Hopefully see them back completed in 3 weeks.

The original plan was to break out the mig and get stuck into completing the body repairs. Business has been good so taking a lot of my time, and my friends had an unexpected gap in their schedule, the KG progress is moving along quicker. A few more discoveries but nothing that cant be fixed.

Price of steel is scary, £90 for some 20mm box, needed for bracing to stop everything moving around;

IMG_5908

235899985_359587338957313_519271555949858547_n

234495404_820019011966747_2359514218897406791_n

IMG_5916

IMG_5915

IMG_5914

IMG_5913

Pile of 58 year old original metal

IMG_5907

Posted: **Thu Aug 12, 2021 8:53 am**

I've said it before - you don't hang about!

Posted: **Fri Aug 13, 2021 8:08 pm**

Todays progress over at the shop

IMG_5919

Floor pan is not welded in yet, so there is a little wave in the panel which will pull down flat during welding;

IMG_5920

IMG_5921

IMG_5922

IMG_5923

IMG_5924

At the rate the guys are going will need to order some more panels up quick

Posted: **Mon Aug 16, 2021 3:39 pm**

Saturdays work;

Outer sill section trial fit and position

IMG_5931

IMG_5934

IMG_5935

Must say these are really good panels, thick gauge sheet metal with accurate fitting. Stranger things have happened, but this is the worst side so maybe the other side will go quicker. I cant jinx it if I don't say it out aloud

Posted: **Mon Aug 16, 2021 5:27 pm**

This is good going!
Great to see the 914 shell in slight dis-array, and getting properly fixed. Looks like the body shop are the first people to get the shell sorted, not local repairs as many suffer in the past?
Agree, you had better get ordering or be accused of slackin'!

Keep thee reports going please.

Posted: **Fri Aug 20, 2021 3:09 pm**

The pile of rusty metal continues to swell.

IMG_5982

IMG_5983

But the good stuff looks much better;

IMG_5956

IMG_5953

Front door gaps looks great

IMG_5958

Rear of door gaps may need a little lead/ filler

IMG_5959

IMG_5944

IMG_5980

The other side

IMG_5976

IMG_5971

IMG_5979

IMG_5975

Posted: **Fri Aug 20, 2021 4:28 pm**

911hillclimber wrote:This is good going!
Great to see the 914 shell in slight dis-array, and getting properly fixed. Looks like the body shop are the first people to get the shell sorted, not local repairs as many suffer in the past?
Agree, you had better get ordering or be accused of slackin'!

Keep thee reports going please.

It’s a Karman Ghia not a 914

Posted: **Sat Aug 21, 2021 9:22 am**

Maybe I have secret plan to turn the engine around and make it a mid-mount Ghia 914

Posted: **Sat Aug 21, 2021 1:57 pm**

See, I'm ahead of you all!

Senior moment so sorry, you will all catch me up sooner or later.

Posted: **Sun Sep 05, 2021 4:16 pm**

Making progress on what will become the drivers side. So both sides and floor are almost finished

Again the door gaps and flush finish is excellent.

The next stage is to move forward to replace the head light buckets, head light surrounds and lower panels. The nose cone is being taken off to straight out the inner side bulk heads and then replaced with a new panel. Seems like any thought of wing panels is not happening. Panels just don't seem to be available. Hope my hammer & dolly skills are up to the task!

Not quite what I was intending but may have found a Type 1 1776 long block at a irresistible price, hope to find out more next week

IMG_6021

IMG_6031

IMG_6029

IMG_6028

IMG_6027

IMG_6026

IMG_6025

IMG_6024 kr

IMG_6023