Page 18 of 66
mirrors
Posted: Thu May 03, 2012 6:04 am
by michel
chris did you come to any decision on what if any external mirror
Re: 912 outlaw project
Posted: Thu May 03, 2012 7:47 am
by johnM
Hi Chris funny I was playing with my headlight wiring yesterday. Just looking at the blue wire looks as if you have it going down the speedo drive hole. I assume you will be still using a mechanical speedo. Didnt want you to run lots of wire to find you have to rip it all back out.
Kind regards.
Re: 912 outlaw project
Posted: Thu May 03, 2012 8:41 am
by jury
johnM wrote:Hi Chris funny I was playing with my headlight wiring yesterday. Just looking at the blue wire looks as if you have it going down the speedo drive hole. I assume you will be still using a mechanical speedo. Didnt want you to run lots of wire to find you have to rip it all back out.
Kind regards.
Cheers for that John, good spot
At the moment it was just placed like that to see if it all works, I had concerns that the ignition was a dud. Now we know the ignition works we will plan the routing, cross-referencing the original loom. The toggle switches will be place in a row on the new dashboard panel, not out of the cigar lighter
Chris
Re: 912 outlaw project
Posted: Sat May 05, 2012 6:34 pm
by jury
Received this in the post the other day.....via contacts in a Chinese shoe factory
Plexiglas logo heat stamp, for the 'plastic' windows.
Prep work...
...and two options delivered, Copper and Aluminium
trial stamping in progress
Chris
Re: 912 outlaw project
Posted: Sat May 05, 2012 6:37 pm
by stretch
Nice one Chris. You sure that wasn't a danish shoe factory.
Re: 912 outlaw project
Posted: Sat May 05, 2012 6:40 pm
by cubist
Ha ha! Truly mental attention to detail... LOVE IT!
I find i'm washing my hands 30 times a day and relocking the door a few times on leaving, just to be sure...
912 outlaw project
Posted: Sat May 05, 2012 7:52 pm
by Gary71
Have you left the gas on though?
Re: 912 outlaw project
Posted: Sat May 05, 2012 7:58 pm
by jury
Takes me ages to leave a hotel room when checking out...I may have used the safe, even though I know I never went anywhere near it
Re: 912 outlaw project
Posted: Sat May 05, 2012 9:01 pm
by jury
3 2 1.....we're back in the room
Re: 912 outlaw project
Posted: Sat May 05, 2012 9:03 pm
by jury
stretch wrote:Nice one Chris. You sure that wasn't a danish shoe factory.
May have had a lay over in Denmark en-route to China
Re: 912 outlaw project
Posted: Sat May 05, 2012 10:22 pm
by KS
What did you do about the two valves? I'm planning on getting the second one TIG-welded up...
Re: 912 outlaw project
Posted: Sat May 05, 2012 11:34 pm
by Nige
Are you going to age the plexiglass print?
Think we are going add a new topic section for yours, Andy's (Lightweight_911) and Mikes projects.
Re: 912 outlaw project
Posted: Fri May 11, 2012 8:53 am
by jury
Project: 'Lets waste abit more time has begun'
Phase 1 complete
Take a perfectly good Fulton U.S military torch...
...and update it abit
The area where it sits in the car is about to begin, and I now know where the vinyl cutter at work is located
Chris
Re: 912 outlaw project
Posted: Fri May 11, 2012 10:57 am
by sladey
Re: 912 outlaw project
Posted: Thu May 24, 2012 1:36 pm
by jury
