Page 10 of 17
Re: Home Built Hot Rod (Full video build)
Posted: Fri Jun 15, 2018 3:38 pm
by defianty
I've been enjoying the engine build up videos Jeff. Very informative.
Re: Home Built Hot Rod (Full video build)
Posted: Mon Jun 18, 2018 9:57 am
by Home Built By Jeff
Thanks Stephen.
My last day at Performance developments, and we finally get onto assembling the bottom end.
https://youtu.be/8-m04Cuamos
Re: Home Built Hot Rod (Full video build)
Posted: Wed May 01, 2019 9:34 am
by Home Built By Jeff
Many of you have been asking me what is happening and I finally have an update for you, and some info on where I am planning to go in the future.
https://youtu.be/n9PrfFX2Wb4
Re: Home Built Hot Rod (Full video build)
Posted: Wed Jul 24, 2019 11:22 am
by Home Built By Jeff
I know it is well overdue, but I am finally getting back onto the 911 and I am going to keep on with it until it is done!
https://youtu.be/fLftkN4zFac
Re: Home Built Hot Rod (Full video build)
Posted: Wed Jul 31, 2019 12:00 pm
by Home Built By Jeff
Piston clips suck! I have finally gotten all of the pistons and cylinders installed on my Porsche 911 2.8 twin plug build, but it was not fun.
https://youtu.be/LQWQRNObjuQ
Re: Home Built Hot Rod (Full video build)
Posted: Wed Aug 07, 2019 11:27 am
by Home Built By Jeff
This is the easy way to measure valve clearance on an aircooled 911 engine.
https://youtu.be/LGeiqyHJKro
Re: Home Built Hot Rod (Full video build)
Posted: Wed Aug 07, 2019 12:08 pm
by Bootsy
Love following your journey!
Re: Home Built Hot Rod (Full video build)
Posted: Thu Aug 08, 2019 5:56 pm
by 911hillclimber
That is a neat way to check a critical dimension, not sure you need to be SO accurate on TDC as the pulley wheel has a factory notch and the human eye is quite accurate to align the block grove and the notch?
Really good series of videos Jeff, never a dull moment!
Re: Home Built Hot Rod (Full video build)
Posted: Fri Aug 09, 2019 12:09 am
by Home Built By Jeff
911hillclimber wrote:That is a neat way to check a critical dimension, not sure you need to be SO accurate on TDC as the pulley wheel has a factory notch and the human eye is quite accurate to align the block grove and the notch?
Really good series of videos Jeff, never a dull moment!
The accuracy is definitely important particularly if the clearances are tight. In this case less so. It is much more important when it comes to the cam timing.
Re: Home Built Hot Rod (Full video build)
Posted: Wed Aug 14, 2019 8:47 am
by Home Built By Jeff
It all comes to a head this week. Or six to be more accurate.
https://youtu.be/MZaeBrQKZ-o
Re: Home Built Hot Rod (Full video build)
Posted: Fri Aug 23, 2019 10:11 am
by Home Built By Jeff
In this episode I continue the build of my 2.8l engine for my 911 and I fit the cam towers.
https://www.youtube.com/watch?v=eUxfWMIuqhQ
Re: Home Built Hot Rod (Full video build)
Posted: Wed Aug 28, 2019 11:29 am
by Home Built By Jeff
In this episode I continue with the 911 engine build and fit the chain boxes.
https://youtu.be/IUxdieqTVxU
Re: Home Built Hot Rod (Full video build)
Posted: Fri Aug 30, 2019 6:59 am
by murph2309
Good effort Jeff - there's a lot of proper learning in these videos..... keep the faith.... not long now.
Re: Home Built Hot Rod (Full video build)
Posted: Fri Sep 13, 2019 8:37 am
by Home Built By Jeff
In this episode I tackle the chain alignment on my old 911 engine which is trickier than it looks. I also clearance and fit my new EFI harmonic balancer.
https://youtu.be/9xRsx9L9ynY
Re: Home Built Hot Rod (Full video build)
Posted: Wed Sep 18, 2019 10:06 am
by Home Built By Jeff
In this episode I tackle the dreaded cam timing. Spoiler alert, it is not as difficult as it seems.
https://youtu.be/OcQ0mgtJ0zA