Hi all, i seek some info about details of the cerametallic lined solid driven plates as fitted in 7.25" competition type clutches, by Tilton, Helix, AP etc.
I use a Quarter Master plate in my Frazer Nash, i bought a second hand 5 plate NASCAR Clutch complete on US Ebay and scavenged 2 Linings and a driven plate from it as an experiment. The principle is close to being a perfect soloution, but i'd like to try a puck type plate to give more bite at launch. The question concerns the PCD of the (8) rivets that attach the splined hub to the Quarter Master plate. I have made a special Frazer Nash to Quarter Master hub and would like to retain this if poss so do AP, Tilton, Helix etc. have the same pattern of rivets? The PCD i seek is 2.125" x 8, or 54mm x 8.
Any help much appreciated, W
7.25" (184mm) Sintered Race Clutch Question
Moderators: hot66, Miggs, 58A - 71E, impmad2000, drummerboytom, Barry, Helen, Viv_Surby, Derek, KS, abm914, Mike Usiskin
-
- Put a fork in me, I'm done!
- Posts: 1816
- Joined: Thu Apr 24, 2008 7:41 pm
- Location: Worcestershire
- Contact:
7.25" (184mm) Sintered Race Clutch Question
Winston
'61 356 BT5 & a lot of broken chain driven stuff
'61 356 BT5 & a lot of broken chain driven stuff
-
- Nurse, I think I need some assistance
- Posts: 19025
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: 7.25" (184mm) Sintered Race Clutch Question
Tony Towson of Super Clutch could be worth contacting, but not sure if they are still trading now.
You could do worse imho asking this question on Uphill Racers forum, a forum of techies involved in hill climbing? You may know them already.
You could do worse imho asking this question on Uphill Racers forum, a forum of techies involved in hill climbing? You may know them already.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: 7.25" (184mm) Sintered Race Clutch Question
Many moons ago I wanted to use a paddle clutch in my race Ultima. I had an ex Mangusta ZF box with a very unusual input shaft spline. I had to get 2 hubs made which I then sent to AP who fitted them to the new plates with no issues. I suggest that you ask them if they can do the same for you.
1970 2.2S Coupe gone
1987 3.2 Carrera Coupe
1989 Kremer 962 CK6 Also gone
1987 962C Sadly sold
1980 935K3 Gone
1987 3.2 Carrera Coupe
1989 Kremer 962 CK6 Also gone
1987 962C Sadly sold
1980 935K3 Gone
-
- Put a fork in me, I'm done!
- Posts: 1816
- Joined: Thu Apr 24, 2008 7:41 pm
- Location: Worcestershire
- Contact:
Re: 7.25" (184mm) Sintered Race Clutch Question
Thanks both, wise words, hadn't thought of sending them the hub! They'll be better at riveting than me too.
W
W
Winston
'61 356 BT5 & a lot of broken chain driven stuff
'61 356 BT5 & a lot of broken chain driven stuff
-
- Me and DDK sitting in a tree! KISSING
- Posts: 2651
- Joined: Fri Apr 18, 2008 5:58 pm
- Location: Sunny Somerset, just above the water....
Re: 7.25" (184mm) Sintered Race Clutch Question
Hi Winston, just checked a Helix plate in the garage, the rivets on that are 56mm PCD x 8.
Sounds a good shout for AP racing - Anthony Lane in Techcraft, Warwick might be able to help.
Cheers
JW
Sounds a good shout for AP racing - Anthony Lane in Techcraft, Warwick might be able to help.
Cheers
JW
Life's a single timed run with no practice....
1970 914/6 2.4E/Webers
1970 VW Beetle project
1972 911 Hillclimber (now 3.5 litre on Management
) Part of the family for 39 years!
2006 Hymer Merc Starline 630
2000 T4 Van LPG
2000 Golf V5 Estate GT
1970 914/6 2.4E/Webers
1970 VW Beetle project
1972 911 Hillclimber (now 3.5 litre on Management
![Shocked :shock:](./images/smilies/icon_eek.gif)
2006 Hymer Merc Starline 630
2000 T4 Van LPG
2000 Golf V5 Estate GT