Page 8 of 18
RHD production numbers ?
Posted: Thu Jul 18, 2013 11:33 pm
by 1968911s
Porsche club GB recent article reported the following UK import data on SWB
1965 imports - 14 cars
1966 imports - 33 cars
1967 imports - 72 cars
1968 imports - 146 cars
total uk imports 265 cars
of the UK imports in 1968, 33/146 were 'S' , 2/146 were slate grey, 3/146 shipped with red interior.
I assume the UK was not the only RHD destination, does anyone know the full production run for RHD?
front wing repair
Posted: Thu Jul 18, 2013 11:46 pm
by 1968911s
repair to turn signal box
and the other wing
Posted: Thu Jul 18, 2013 11:49 pm
by 1968911s
the rot on this side was much worse
further blinker box repairs
Posted: Thu Jul 18, 2013 11:52 pm
by 1968911s
further turnsignal box repairs to front wing
final turnsignal repairs
Posted: Thu Jul 18, 2013 11:55 pm
by 1968911s
final turnsignal repairs
rear crossmember rot!
Posted: Sat Jul 27, 2013 9:33 pm
by 1968911s
Sand blasting of underside reveals rot in the rear crossmember on one side only
yellow canary transplant
Posted: Sat Jul 27, 2013 9:37 pm
by 1968911s
I section of yellow canary to the rescue..
transplant
Posted: Sat Jul 27, 2013 9:41 pm
by 1968911s
donor is cleaned and welded into place
crossmember repaired
Posted: Sat Jul 27, 2013 9:43 pm
by 1968911s
all welds cleaned up
Re: So it started with an MOT.... in 2012
Posted: Sun Jul 28, 2013 10:51 pm
by 1968911s
interested to know the correct location for attaching the larger durant door mirror
Re: So it started with an MOT.... in 2012
Posted: Wed Jul 31, 2013 5:19 am
by sleeper
Have you ever considered taking up as a plastic surgeon. Your work is pure artisan.. Well done
onto the shaping
Posted: Thu Aug 01, 2013 12:01 am
by 1968911s
ironing out the lumps and bumps ahead of priming, can't wait to see the car in all one colour again..
away from the bodywork the calipers were sent for restoratio
Posted: Thu Aug 01, 2013 12:16 am
by 1968911s
So I lugged 4 callipers to the US as hand luggage, I have to say the i didn't appreciate the long wait as passport control.. In 1968 the front callipers were M castings in Steel, and Wide L on the rear.
The rears were in bad condition externally, but pistons came out ok.. corrosion was meant that the rare fasteners could not be salvaged, I asked that we try to restore them if they would be operationally upto the task, these were the worst callipers the specialist has ever seen.
callipers
Posted: Thu Aug 01, 2013 12:22 am
by 1968911s
So 45 years of english climate has not been kind to these units, restoration of my callipers worked around other jobs as it was not clear we would be able to get them apart, but after much soaking they did come apart, I was at this point considering if I should simply buy alternative 'correct' callipers and if the expense here was going to justify the outcome, but they did come apart, so we sent them off for coating..
...and whist pitted they have cleaned and the bores were good.
1968 911 Callipers
Posted: Thu Aug 01, 2013 12:26 am
by 1968911s
And to the finished product, I am happy that we have managed to breathe like back into the original callipers, especially as these are parts that are specific to the model year.