Mashed flywheel ring gear
Moderators: hot66, impmad2000, Barry, Viv_Surby, Derek, Mike Usiskin
Re: Mashed flywheel ring gear
I'd still want to eyeball it in operation to make sure it engages ok. Note sure if there is any visibility though. The on the pintos and xflows you can eyeball it. We've videoed it on a phone and played back the video in slow mo to check it before now
-
- Nurse, I think I need some assistance
- Posts: 18932
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Mashed flywheel ring gear
No chance to see the engagement with a 915 box, the pinion is totally shrouded.
Nothing stopping you from fitting the current starter to the engine/box out of the car on the floor and switch 12v to the starter and hear if it is a clean action and repeatable.
Nothing stopping you from fitting the current starter to the engine/box out of the car on the floor and switch 12v to the starter and hear if it is a clean action and repeatable.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Mashed flywheel ring gear
I’ve now split the engine and gearbox, and will get some pics later.
Many of the flywheel teeth are damaged on their end face - the screeching sound was the starter pinion spinning against the tooth end faces rather than fully extending to engage and turn the flywheel - effectively machining the end faces of the teeth for a second or so, before eventually popping into mesh. Not great!
Sent from my iPhone using Tapatalk
Many of the flywheel teeth are damaged on their end face - the screeching sound was the starter pinion spinning against the tooth end faces rather than fully extending to engage and turn the flywheel - effectively machining the end faces of the teeth for a second or so, before eventually popping into mesh. Not great!
Sent from my iPhone using Tapatalk
Gavin
'73 911E -> 2.7mfi
'94 968 Sport
'73 911E -> 2.7mfi
'94 968 Sport
Re: Mashed flywheel ring gear
Sent from my iPhone using Tapatalk
Gavin
'73 911E -> 2.7mfi
'94 968 Sport
'73 911E -> 2.7mfi
'94 968 Sport
-
- Nurse, I think I need some assistance
- Posts: 8753
- Joined: Sat Apr 23, 2005 9:08 pm
- Location: Nottingham, UK
Re: Mashed flywheel ring gear
DONT!gav p wrote:On the Powerlite website i see that their starters have a couple of different bevels on the tooth edges. See pic here. Subtly different from mine. I’ve also seen comments on Andy Prill’s website, where he sells Powerlite starters, that flywheel damage has been a recognised issue with some other aftermarket starters.
Tempted to try the Powerlite.
Sent from my iPhone using Tapatalk
I can’t put a link on here (I’m on Tapatalk and can’t see how) but search for my previous thread “feckin starter motor” or just search lightweight starter and it comes up.
By all means read the whole thread but skip to the end for the important bit
I’ve had a lot of problems with a power lite one and just replaced it with a wosp one and I put side by side pics on the thread.
The wosp one fits better and starts the car loads better. The failed power lite one wasn’t that old either
HTH
The simple things you see are all complicated
I look pretty young but I'm just backdated yeah
I look pretty young but I'm just backdated yeah
-
- Put a fork in me, I'm done!
- Posts: 1641
- Joined: Fri Mar 01, 2013 11:45 am
- Location: Kernow - good old Cornwall
Re: Mashed flywheel ring gear
Thanks for the heads-up!!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Gavin
'73 911E -> 2.7mfi
'94 968 Sport
'73 911E -> 2.7mfi
'94 968 Sport
Re: Mashed flywheel ring gear
Had a very similar issue on my 2.0 car with 901 gearbox. The teeth (integral to flywheel) and been completely chewed away. Concluded that maybe the starter hadn't been disengaging properly, but never entirely sure. Swopped the flywheel and starter, put it back together and forgot about it.
Now I'm tempted to pull the starter and eyeball the ring gear. It hasn't done many miles since the fix but would like to be sure the problem doesn't remain.
From memory, I don't recall anything to ensure precise location of the starter i.e. location dowels or bushes. Is this correct?
Cheers,
Chris
Now I'm tempted to pull the starter and eyeball the ring gear. It hasn't done many miles since the fix but would like to be sure the problem doesn't remain.
From memory, I don't recall anything to ensure precise location of the starter i.e. location dowels or bushes. Is this correct?
Cheers,
Chris
'68 swb 911L
'62 Lotus 22
100cc Historic Karts
'62 Lotus 22
100cc Historic Karts
Re: Mashed flywheel ring gear
On my car the starter position has no inherent adjustment- its just located by the two mounting studs and the machined spiggot on the mating face of the starter fitting into the bell housing.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Gavin
'73 911E -> 2.7mfi
'94 968 Sport
'73 911E -> 2.7mfi
'94 968 Sport
Re: Mashed flywheel ring gear
I’ve now gone ahead and bought a Wosp starter - quality looks good on the face of it, and the pinion teeth leading edges look nicely bevelled.
But, i now need to buy a ring gear - turns out that I don’t have a spare after all. Anyone got one they’re not using? Looks like these are on back order and not currently in stock.
Part number 91111623904
Sent from my iPhone using Tapatalk
But, i now need to buy a ring gear - turns out that I don’t have a spare after all. Anyone got one they’re not using? Looks like these are on back order and not currently in stock.
Part number 91111623904
Sent from my iPhone using Tapatalk
Gavin
'73 911E -> 2.7mfi
'94 968 Sport
'73 911E -> 2.7mfi
'94 968 Sport