Engine stand yoke
Moderator: Bootsy
Engine stand yoke
Engine yoke is constructed of thickwall steel pipe and cnc plasma cut 6mm heavy plate steel.
Fits all air-cooled VW and Porsche engines/transaxles.Engine mounting ring and four arm design reduces the chance of case damage. Engine yoke fits most roll-round stands(Clark/sealy)with a 60mm ID.£70 plus £10 post
jack.purse@outlook.com
Fits all air-cooled VW and Porsche engines/transaxles.Engine mounting ring and four arm design reduces the chance of case damage. Engine yoke fits most roll-round stands(Clark/sealy)with a 60mm ID.£70 plus £10 post
jack.purse@outlook.com
Last edited by Beetlejac on Tue Aug 08, 2017 7:04 pm, edited 3 times in total.
Re: Engine stand yoke
hia, is this for allI can see, as in stand and the two spiders?
cheers dave
cheers dave
Re: Engine stand yoke
No just the YOKE,thats the black bit,and just the one.
thanks
jack
thanks
jack
-
- Nurse, I think I need some assistance
- Posts: 18924
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Engine stand yoke
Will this fit a 3.2 911 engine?
Not sure if your description means all 4 cylinder engines or includes the 6 cylinder?
Not sure if your description means all 4 cylinder engines or includes the 6 cylinder?
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Engine stand yoke
I think marginal Graham as 3.2 with stock equipment is close to the SWL - does not allow much leeway if you are undoing camshaft nuts at 100 ft/lbs. Do you have steelcap boots?
Regards...Chris
Regards...Chris
Porsche - Diesel, the next most affordable Classic
-
- Nurse, I think I need some assistance
- Posts: 18924
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Engine stand yoke
That is why I asked!
The 3.2 is a mighty lump fully dressed.
The 3.2 is a mighty lump fully dressed.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Engine stand yoke
Hi that SWL you see is for the actual stand not the yoke/spider,l have been making the rings wider so they look stronger and have more surface contact and at the end of the day its only realy two M10 bolts thats holding the engine on the yoke/spider.
The welds are'nt going to fail and with the weight spread over the four arms l cant see them failing and bending.The yoke's only as good as the stand its mounted to.
Hope that helps
jack
The welds are'nt going to fail and with the weight spread over the four arms l cant see them failing and bending.The yoke's only as good as the stand its mounted to.
Hope that helps
jack
Re: Engine stand yoke
Bench mounted,heavy duty £90
Last edited by Beetlejac on Sat Jan 18, 2014 7:17 pm, edited 1 time in total.
Re: Engine stand yoke
do you sell this ?Beetlejac wrote:Bench mounted,heavy duty £80
fred ©
-
- Nurse, I think I need some assistance
- Posts: 18924
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Engine stand yoke
I would actually like to buy one of your Yokes, heavy duty, not with the bench mounting, but for the engine stand tube.
Please pm the cost to me.
Do you take paypal, and are these 'in stock' so to speak?
If not how long is your lead time?
Thanks,
Graham.
Please pm the cost to me.
Do you take paypal, and are these 'in stock' so to speak?
If not how long is your lead time?
Thanks,
Graham.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Engine stand yoke
PM sent.
-
- Nurse, I think I need some assistance
- Posts: 18924
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Engine stand yoke
Job done.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Re: Engine stand yoke
I'd like a bench mounted one please?
-
- Nurse, I think I need some assistance
- Posts: 18924
- Joined: Mon Mar 10, 2008 6:26 pm
- Location: West Midlands
Re: Engine stand yoke
Mine arrived today, looks good and fits my Clark stand a treat.
It needs a 10mm hole(s) drilling to secure the 'angle' of the frame as you work on the engine, but no problem.
Chuffed!
Graham.
It needs a 10mm hole(s) drilling to secure the 'angle' of the frame as you work on the engine, but no problem.
Chuffed!
Graham.
73T 911 Coupe, road/hillclimber 3.2L
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9
Lola t 492 / 3.2 hillclimb racer
Boxster 987 Gen II 2.9